6308-2RSR-C3-manufacture,factory,supplier from China

Product IntroductionModel: 6308-2RS C3 Deep Groove Ball BearingInner diameter: 40mmOuter diameter: 90mmHeight: 23mmWeight: 0.639kgDynamic load: 40.8Static load: 24Grease speed: 7800Oil speed: 9200Retainer: Steel plate stamping retainerMaterial: Bearing steel, GCR15Appearance: Exquisite, shiny, without scratches or bumpsPackaging: Industrial packaging or individual color box packagingBearing No.Boundary Dimensions(mm)Basic Load Ratings(KN)WeightOPENShieldsSealsdDBCrCorKg(pc)6300ZZ2RS10 35 11 8.10 3.45 0.053 6301ZZ2RS12 37 12 9.70 4.20 

Product Introduction6001ZZ/C3 Deep Groove Ball Bearing composed of a pair of rings, a set of retainers, and a set of steel balls.

Product IntroductionThe dimensional parameters of 6211ZZ/C3 Single Row Ball Bearings include an inner diameter of 12mm, an outer diameter of 28mm, and a width of 8mm.

Product Introduction6207 ZZ/C3 Deep Groove Ball Bearing is the most representative rolling bearing. 6207 ZZ/C3 Deep Groove Ball Bearing consisting of a pair of rings, a set of cages, and a set of steel balls.

Product Introduction6006-2RS/C3  Bearing is belong to deep groove ball bearing .Also called single row deep groove ball bearing .Bearing No.Boundary Dimensions(mm)Basic Load Ratings(KN)WeightOPENShieldsSealsdDBCrCorKg(pc)6000ZZ2RS10 26 8 4.55 1.95 0.019 6001ZZ2RS12 28 8 5.10 2.40 0.022 6002ZZ2RS15 32 9 5.60 2.85 0.030 6003ZZ2RS17 35 10 6.00 3.25 0.039 6004ZZ2RS20 42 12 9.40 5.05 0.069 6005ZZ2RS25 47 12 10.10 5.85 0.0

Product Introduction203KRR2 Agriculture Bearing belongs to non-standard sprocket bearings.

Product IntroductionThe dimensional parameters of SFC 30309 Tapered Roller Bearing include an inner diameter of 45.000 mm, an outer diameter of 100.000 mm, and a thickness of 27.250 mm.

Product IntroductionBearing type: tapered roller bearing       Domestic new model: 32016         Domestic old model: 2007116EInner diameter (mm): 80      Outer diameter (mm): 125          Width (mm): 29Lubricating speed (r/min): 3000          Cor(kN)：220             Cr(kN)：140Oil lubrication speed (r/min): 3800                 Weight (KG): 1.2732016 tapered roller bearing adopt super finishin

Product Introduction32008X Tapered Roller Bearing produced by well-known brand SFC, belongs to the 30000 type of tapered roller bearings. The previous old model was 2007108E, And the specific parameters of 32008X Tapered Roller Bearing are: Inner diameter- 40mm, Outer diameter- 68mm, Thickness -19mm.Please refer to the following table for specific parameters of 32008X tapered roller bearing and other bearings in the same seriesBearing TypeBasic dimensionsLimit speedRated loadWeight(kg)New TypeOriginal Type(mm)d(mm)DAssembly height(mm)TGreaseOilDynamicStatic32

High-Quality Automotive Bearings 6-256907 & 6-256706 – Precision, Durability, and PerformanceEnsure smooth performance and reliable operation with our premium automotive bearings, part numbers 6-256907 and 6-256706.

Product Introdution  HGH30CA Block ，The height is 39mm, the width is 60mm, and the length is 97.4mm. HGH30CA  Block  is used with HGR30 linear guide rail. HGH30CA  Block  has high bearing capacity and can automatically adjust and absorb the assembly error of the mounting surface.

Product Introdution  HGH45CA Block is a heavy-duty series guide rail, with a combined height of 60mm with HGR45 guide rail.

Product Introdution  MGN15C Slide Block is a micro series guide rail with a combined height of 16mm and an installation hole size of 25 * 20.

Product Introdution  EGH15SA Block is a low assembly linear series guide rail with only 2 mounting holes, The combined height of EGH15SA Block is 24mm, and the mounting hole size of EGH15SA Block is 26mm. The linear guide rail return hole is specially designed with a steel ball return hole and a return passage composed of a fully sealed plastic frame and a plastic end cover.

Product IntroductionModel: Self aligning ball bearing 2313/2313KBrand: SFC (Also can do OEM orders)Self aligning ball bearing 2313 dimension:Inner diameter: 65 mmOuter diameter: 140 mmThickness: 48 mm Self aligning ball bearing 22 Series:ITEMSDimensionsWeight(kg)inner diameterouter diameter thickness22001030140.04822011232140.05322021535140.05822031740160.08922042047180.1422052552180.1622063062200.2622073572230.4122084080230.522094585230.5322105090230.57221155100250.79221260110221.05221365120311.4221470125311.5221575130311.6221680140332221785150362.5221890160403.42219951704

Product IntroductionUCHA205-16 Pillow Block Ball Bearing is hanging type bearing.Inch size type.The height is 103mm,bottom width:40mm,the widest is 78mm.And the whole weight depend on the housing weight.UCHA205-16 Pillow Block Ball Bearing adopt local heat treatment technology,improve toughness.When you tighten the screw,not cause inner ring cracking,long use life.And top screw,have ball nuts and common type.About housing material,we usually use HT200 material,go by tensile testing,compared with HT180 housing,not easily broken.Match with bearings more smoothly.Although HT180 cost is cheaper,bu

Product IntroductionThe sliding unit of SBR Supported Rods bearing block assembly is a sliding unit composed of box-type linear bearing, high hardness LM Shaft and anti-deflection aluminum rail. High-hardness shaft (45# Steel after high-frequency heat treatment, hardness HRC55-60, hard chrome plating on the surface) and anti-deflection aluminum rail (anodized high-strength aluminum alloy for the box) The screw holes required for installation are after the shaft is hardened.

Product IntroductionUCFC206 Pillow Block Ball Bearing is composed of a circular flange seat and an outer spherical bearing 206. The inner hole adopts a local annealing process to improve toughness. When tightening the screw, it will not cause the inner ring to break, and the service life is longer.

Product Introduction DAC42840036 Wheel Hub Bearing is belong to First generation automotive bearings，This item number marked in SKF is BA2B444090AB,in FAG is 564727,in SNR is GB10857 S02,in IRB is IR-8039.Except our brands, we also can deal with OEM.  If you are finding this auto bearing,kindly contact us.The main function of a hub bearing is to bear weight and provide precise guidance for the rotation of the hub. It bears both axial and radial loads and is a very important component.

Product IntroductionUCP206 Pillow Block Ball Bearing is a combination of one UC206 outer spherical bearing and one P206 Housing. There are also UCP206-18, UCP206-19, and UCP206-20 in the same seriesItem:UCP206 Pillow Block Ball BearingBrand: SFC/OEMInner diameter d: 30mmOuter diameter D: 165mmThickness:42.9mmWeight:1.1 kgsPlease download the specific parameters of UCP206 Pillow Block Ball Bearing from the homepage download center.

Product IntroductionThe UCP201 Pillow Block Ball Bearing consists of two sealed outer spherical ball bearings and a cast (or steel plate stamped) bearing seat.  Usually, there is a gap between the inner hole of The UCP201 Pillow Block Ball Bearing and the shaft.

Product IntroductionThis Pillow Block Ball Bearing UCP207 adopts a thickened material seat with a solid bottom, which is more sturdy, durable, and less prone to damage. Simultaneously using high-quality steel, carefully grinding, efficient coordination, and worry free operation.

Product IntroductionUCF208 Pillow Block Ball Bearing , Flange Bearing,according to the bearing quality have common quality,high quality.According to the housing material,rough divided into three categories:HT160,HT180,HT200.We usually adopt the best material-HT200.Undergoing tensile testing,not prone to brittle fracture.Like P housing has high quality requirments,if use cheaper low-end housing,assemble the bearings inside,squeezed,then out of shape,also impact speed.Here are UCF208 Pillow Block Ball Bearing , Flange Bearing parameters:Unit No.Shaft Dia.          &

Product Introdution  HGH35CA Block，its dimensions is 47.5mm*70mm*112.4mm.  HGH35CA Block  is used with HGR35 linear guideway together. The combined height of the complete set is 55mm.(For more parameters about HGH35CA  Block or more Linear series products, please visit the home page to download the E-catalog)SpecificationHGH35CA BlockDimensions of AssemblyH55mmH17.5mmN18mm Dimensions of Block W70mmB50mmB110mmC50mmL180mmL112.4mmK120.6mmK27mmG12mmMxlM8x12mmT10.2mmH216mmH319.6mmDimensions of HGR35 RailWR34mmHR29mmD14mmh12mmd9mmP80mmE20mmMounting B